| From | Message |
Roy
9/02/2010
08:06:38
|
 Subject: Canon Imageclass D860 miss feeds
IP: Logged
Message:
I can't believe I'm stumped on this. You can feed from bypass tray with no issues. When feeding from paper tray it shuts down with the paper hanging out of the fuser and says recording paper jam. I/ve changed the feed tires and the one way bearing on the transport turn roller. You can feed singles or doubles from the paper tray all day long. No problem. Try to do more than three or four copies from the tray...missfeed with the paper hanging out the fuser and one in the turn guide. There is no jam. Just a miss feed shut down. What am I missing? I've cleaned everything I can think of. There ain't nothing there. Has anyone run into this before?
Roy
|
tom
9/02/2010
13:01:26
| RE: Canon Imageclass D860 miss feeds
IP: Logged
Message:
sounds to me like it might be set for the wrong size paper. eg. set for executive but seeing letter
|
Robert
9/02/2010
19:22:31
|  RE: Canon Imageclass D860 miss feeds
IP: Logged
Message:
seen the feed solenoid noise bumper deteriorate and the glue part makes the rollers turn when not needed causing jam. selenoid sticks activated
flip machine on its top bottom up remove shield.
take selonoid out 1 screw remove spring from selenoid and thorougly clean all glue of the noise cusion. live with the noise it will feed great!
|
Cope
9/02/2010
20:14:43
| RE: Canon Imageclass D860 miss feeds
IP: Logged
Message:
If the machine has a lot of clicks you may have a
worn down regsensor flag...easy fix. Pull the
toner cartridge out and look at the metal flap
that pushes the paper down on the reg sensor as it
comes out of the turn. Push down on it in the
middle bending it ever so slightly so that it puts
more pressure on the paper thereby pushing the reg
sensor flag more reliably. Problem solved with no
tools. Now run a few Roller Cleaning cycles
because jams in the fuser will leave toner build
up in the fuser which can easily lead to the death
of the machine when the user stabs it with a
letter opener. Good luck -Cope
|
Clickman
9/03/2010
08:22:13
| RE: Canon Imageclass D860 miss feeds
IP: Logged
Message:
also check the segment roller just after the cassette
the frame that holds it in place break and the roller floats around in and out of position
there is a frame repair
Product Overview:
CANON IMAGECLASS D860 KIT - Retainer Shaft Maintenance Kit - Rear Shaft Bushing Housing Repair Kit Located in the Paper Feed Assembly - This Kit Includes Necessary Parts, Installation Procedure and a Sticker for the User to be Attached to the Machine - Genuine Canon Kit
Mfr Part #: FG6-9554-000, FG6-9887-000
PR Order #: J6544
|
Gideon
9/06/2010
21:00:03
| RE: Canon Imageclass D860 miss feeds
IP: Logged
Message:
There is a legal detection switch above the paper tray to the left, ?. I had similar problem and couldn't solve it
|
Roy
9/09/2010
15:11:18
| RE: Canon Imageclass D860 miss feeds
IP: Logged
Message:
It turned out to be the fuser assy. Swapped it with another machine and the problem went away. I can't explain it, the fuser works fine in another copier, but not in that one. I'd really like an explanation for this one!
Roy
|
Cope
9/14/2010
14:21:10
| RE: Canon Imageclass D860 miss feeds
IP: Logged
Message:
Possibly fuser film drag. If the other machine it
swapped into had a lower cpm (there were different
fusers but the only difference was spring tension)
it could be dragging at higher speeds and temps.
Just a guess. congrats now sell em a toner. -Cope
|